{Stus-List} Mainsheet system shortening

Sam Salter sam.c.salter at gmail.com
Sun Jan 16 12:02:05 EST 2011


I'd think this strop many people are suggesting, would be the perfect fit for "Dynema"rope.
Not too expensive at 2 ft plus the splices; Nothing to get cut on.
Soft like baby's bum; Strong like tractor!
Sam :-)
C&C 26  Liquorice
Ghost Lake  Alberta
(I'd give my right arm to be ambidextrous!)

On 2011-01-16, at 6:09 AM, dwight veinot <dwightveinot at hfx.eastlink.ca> wrote:

> Dennis
>  
> I use such a strop, made of covered wire, like life line wire.  It’s about 2 feet long and I have a 7:1 mainsheet system with a ratchet block and cleat on the traveler.  The strop educes about 14 feet on the main sheet; I like the way it works.  As you know the traveler on my 35MKII is on the bridge deck and the block hanging from the boom has never once been an issue for anyone on the boat.
>  
> D. Veinot
> From: cnc-list-bounces at cnc-list.com [mailto:cnc-list-bounces at cnc-list.com] On Behalf Of Dennis C.
> Sent: January 15, 2011 6:55 PM
> To: cnc-list at cnc-list.com
> Subject: Re: {Stus-List} Mainsheet system shortening
>  
> Chuck, all
>  
> I've thought about shortening my 6:1 system with a strop but don't like the idea of the block hanging a couple feet below the boom.  I keep envisioning a crew getting whacked with it during a gybe. 
>  
> Any good thoughts on a better solution?
>  
> Dennis C.
> Touche' 35-1 #83
> Mandeville, LA
>  
> From: "cscheaffer at comcast.net" <cscheaffer at comcast.net>
> To: cnc-list at cnc-list.com
> Sent: Sat, January 15, 2011 11:28:36 AM
> Subject: Re: {Stus-List} Mainsheet system on C&C 35-III
> 
> Another thought:
> When cruising, I usually have the autohelm steering and I'm mostly in the cockpit, forward of the wheel, where I can monitor the GPS, check the chart on the seat, and easily reach everything; jib sheets, mainsheet, traveller crosshauls, backstay hydraulics, halyards, cunningham, vang, mainsail outhaul, etc.  I'm closer to the cabin and the ice box, galley, and tea kettle.   Locating the traveller closer to the mast shortens the mainsheet considerably, and one of the best setups can be found on racing/crusing Beneteaus, where they mount two travellers on the boat.  Coachtop for cruising and cockpit for racing.  The coachtop traveller uses a very short mainsheet compared to the cockpit mounted racing version and there is no spaghetti on the cockpit floor.
> 
> Another thought::
> A long end-of-boom mainsheet can be shortened somewhat by adding a strop between the boom bail and the upper block of your purchase.  Our 34R needs about 120 ft of mainsheet to allow the boom with a 6:1 purchase to go out for downwind sailing.  Adding a 3 ft strop will shorten the line 18 feet which will reduce some spaghetti on the floor, clear the helm's view a little and possibly make adjustments quicker when close hauled?   I plan to makeup an amsteel strop this winter in 1/4" amsteel.  
> 
> Chuck
> Resolute, 1990 C&C 34R
> 
> 
> 
> ----- Original Message -----
> From: "Tim Goodyear" <timgdyr at gmail.com>
> To: cnc-list at cnc-list.com
> Sent: Saturday, January 15, 2011 10:45:30 AM
> Subject: Re: {Stus-List} Mainsheet system on C&C 35-III
> 
> Thanks for the updates.  I forgot to mention that we have 3/4 boom
> sheeting with the traveller across the companionway bridge deck.  The
> new traveller is Harken big-boat with a five to one purchase and lines
> led up the cockpit sides for trimming on the rail. This is too far
> forward for the helm to reach easily, but has worked ok for cruising.
> 
> Thanks,
> 
> Tim
> On Saturday, January 15, 2011, John and Maryann Read
> <johnpread at comcast.net> wrote:
> >
> >
> >
> >
> >
> > Tim
> >
> > Our 34
> > has mid boom sheeting.  Single Harken 3 sheave blocks on traveler and
> > boom.  Had to install larger bale on boom when original broke.
> > Sheet goes forward to mast then aft to 2 speed winch on cabin roof next to
> > companionway - I think it is a Barient 22.  Traveler is Harken big boat
> > series with cam cleats each side.  Works very well.   One crew is
> > dedicated to trimming main and winch provides more than enough power to
> > trim even if fully loaded.  All lines hang down below so are out of
> > the way.  That crew stands in companionway and is out the way of other crew
> > but can easily reach out a hand to help if needed.  Easy to play traveler
> > going upwind to balance the rig during puffs.  Interesting to note that
> > from my position on the helm I can see the boom actually sagging when fully
> > trimmed in a breeze.  The downside is the helmsman can not easily trim the
> > main
> > John & Maryann Read
> > Legacy III
> > 1982 C&C 34
> > Noank, CT
> >
> >   -----Original Message-----
> > From:
> >   cnc-list-bounces at cnc-list.com [mailto:cnc-list-bounces at cnc-list.com]On
> >   Behalf Of Tim Goodyear
> > Sent: Friday, January 14, 2011 3:27
> >   PM
> > To: cnc-list at cnc-list.com
> > Subject: {Stus-List}
> >   Mainsheet system on C&C 35-III
> >
> >
> >   I'm going to change out my mainsheet system this year to replace some
> >   worn blocks / cleat, as well as trying to make it kinder to the mainsail
> >   trimmer and making that position accessible to more people.  The
> >   traveller upgrade forced on me when the car disintegrated last year is
> >   wonderful and I wish I had done it before.  What do people use for their
> >   mainsheets, how do they find them (especially for racing)?  What line do
> >   people use?
> >
> >   My current setup is a 5:1 with a fine-tune inside the boom (that rarely
> >   gets used).  I'm thinking of going to a 6:1 or 8:1 two-speed
> >   and getting rid of the fine-tune.  The main
> >   issue with the current system has been getting the final bit of trim on
> >   (the fine tune would help there) and being able to dump quickly if needed
> >   (fine tune can't help).  Something like the Ronstan RF72900 or Harken
> >   equivalent would probably work, but that is a little pricey and will mean
> >   a lot of line in the cockpit...
> >
> >   Thanks,
> >
> >   Tim
> >
> >   Mojito
> >   C&C 35-III
> >
> 
> _______________________________________________
> This List is provided by the C&C Photo Album
> http://www.cncphotoalbum.com
> CnC-List at cnc-list.com
>  
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1191 / Virus Database: 1435/3380 - Release Date: 01/14/11
> _______________________________________________
> This List is provided by the C&C Photo Album
> http://www.cncphotoalbum.com
> CnC-List at cnc-list.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://cnc-list.com/pipermail/cnc-list_cnc-list.com/attachments/20110116/e986afe9/attachment-0002.html>


More information about the CnC-List mailing list