Stus-List Re-wiring, looking for suggestions

Joe Della Barba joe at dellabarba.com
Fri Feb 17 20:55:10 EST 2017


Nothing wrong with Paneltronics, I just could never find them on FleaBay. BlueSeas has *lighted* labels that I really like. I can’t recall if the others do.

 

Joe Della Barba

joe at dellabarba.com

From: CnC-List [mailto:cnc-list-bounces at cnc-list.com] On Behalf Of Paul Wyand via CnC-List
Sent: Friday, February 17, 2017 1:34 PM
To: cnc-list at cnc-list.com
Cc: Paul Wyand <miatapaul at gmail.com>
Subject: Re: Stus-List Re-wiring, looking for suggestions

 

I used Paneltronics, at least equal quality to Blue Seas. Customer service was excellent too, and will make up a custom panel as well for little extra cost. I asked a few questions before the panel was delivered and they gave me very accurate an rapid answers. I had such good service I will use them from now on. I am sure they use the same breakers as Blue Seas as I doubt either one makes there own. Panel thickness was very good, and wiring was neatly run. 

 

On Fri, Feb 17, 2017 at 1:23 PM, Alex Giannelia via CnC-List <cnc-list at cnc-list.com <mailto:cnc-list at cnc-list.com> > wrote:

Mathew



Thanks,


Alex Giannelia
ag at airsensing.com <mailto:ag at airsensing.com> 
(416) 203-9858 <tel:%28416%29%20203-9858> 


Message: 2
Date: Fri, 17 Feb 2017 07:51:50 -0500
From: "Matthew L. Wolford" <wolford at erie.net <mailto:wolford at erie.net> >
To: <cnc-list at cnc-list.com <mailto:cnc-list at cnc-list.com> >
Subject: Re: Stus-List Re-wiring, looking for suggestions
Message-ID: <45ACD1AB55D6494CBCA1FF12A30A99B9 at InternetPC>
Content-Type: text/plain; charset="utf-8"

In response to one of your queries below: I like circuit breakers for both AC and DC; I like Blue Sea Systems; and I do not like panels that combine AC and DC.  I replaced the original fuse panel on my 34 with two BSS DC circuit breaker panels (one relatively large, and the second because I needed more breakers).  To get them to fit in the old fuse panel configuration, I had a fabricating shop make an aluminum frame the same size as the old panel (about $50), with cut-outs for installing the BSS panels.  I then sent the aluminum frame to BSS, and they painted or powder-coated it (or whatever they do) so that it matched their panels ? and they did this for free because I was using their circuit breaker panels.  I also replaced the clunky old AC breaker box with a small BSS circuit breaker with polarity indicator.  I also installed a BSS switch that keeps the house and engine batteries separate but can cross connect in the event of a problem with the engine battery.  Great sys!
 tem, which I?m considering for my ?new? boat (a 42).

From: Alex Giannelia via CnC-List
Sent: Friday, February 17, 2017 1:49 AM
To: cnc-list at cnc-list.com <mailto:cnc-list at cnc-list.com> 
Cc: Alex Giannelia
Subject: Stus-List Re-wiring, looking for suggestions

So, the old girl came off the hard, has a new electric motor and is now going to get new cabin wiring.



I have been reading about bonding, grounding, panels, etc. and my head is spinning, so thought I ?d turn to the list for some collective wisdom



Here?s a few:



What sort of panels do people recommend?  The spread is for a couple hundred bucks for a fuse panel to well over a grand for a combined AC/DC Blue Seas baby.



I am removing the old combined AC/DC panel above the companionway with one 6 gang panel in the cockpit and a 12 position plus 3 AC at the Nav Station.



SHORE POWER



Ok, so who is using an isolation transformer?



Do you connect the DC Negative at the battery with the AC ground on your incoming?



BONDING/LIGHTNING PROTECTION



Who connects all the rig, prop shaft and keel in one electrical bundle also connected with battery ground?  Has anyone ever considered bonding the aluminum toe rails?



RFI shielding



What do you guys do to reduce RFI cross talk?



That?s it for now.



This will be a simple boat, VHF, GPS Simrad WP30 Wheelpilot and Standard Instruments.  The power supply for the electric motor was done already by a marine electrical guy and works extremely well.



Suggestions?



Let ?er roll!




Alex



Alex Giannelia

C&C 35-II (1974) no 282

ag at airsensing.com <mailto:ag at airsensing.com> 



_______________________________________________

This list is supported by the generous donations of our members. If you wish to make a contribution to offset our costs, please go to:  https://www.paypal.me/stumurray

All Contributions are greatly appreciated!

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://cnc-list.com/pipermail/cnc-list_cnc-list.com/attachments/20170217/58c2eafd/attachment-0001.html>


More information about the CnC-List mailing list